Testing and Prediction of Thermal-Mechanical Fatigue Crack Growth Rates in NiAl Superalloy

HE Yu huai; LIU Shao lun; ZHAO Xi hong

Chinese

您当前的位置：

首页 >

文章列表页 >

Testing and Prediction of Thermal-Mechanical Fatigue Crack Growth Rates in NiAl Superalloy

更新时间：2026-07-07

- Testing and Prediction of Thermal-Mechanical Fatigue Crack Growth Rates in NiAl Superalloy
- Vol. 17, Issue 1, Pages: 93-96(2002)
- 作者机构：
  
  北京航空材料研究院,北京,100095
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2002
- 稿件说明：
移动端阅览
何玉怀, 刘绍伦, 赵希宏. Ni3Al合金热/机械疲劳裂纹扩展速率试验及其预测研究[J]. 航空动力学报, 2002, 17(1): 93-96.

HE Yu huai, LIU Shao lun, ZHAO Xi hong. Testing and Prediction of Thermal-Mechanical Fatigue Crack Growth Rates in NiAl Superalloy[J]. 2002, 17(1): 93-96.
何玉怀, 刘绍伦, 赵希宏. Ni3Al合金热/机械疲劳裂纹扩展速率试验及其预测研究[J]. 航空动力学报, 2002, 17(1): 93-96. DOI：

HE Yu huai, LIU Shao lun, ZHAO Xi hong. Testing and Prediction of Thermal-Mechanical Fatigue Crack Growth Rates in NiAl Superalloy[J]. 2002, 17(1): 93-96. DOI：

摘要

本论文对 Ni3Al高温合金进行了 45 0℃～ 990℃热 /机械疲劳裂纹扩展行为的试验研究与宏微观分析。分别研究了相位角、保持时间、温度、频率对 Ni3Al合金裂纹扩展行为的影响。研究发现:温度的升高和频率的降低均会加速裂纹扩展; 同相位热 /机械疲劳裂纹扩展速率大于反相位热 /机械疲劳裂纹扩展速率

而且它们两者介于最大温度和最小温度的等温疲劳裂纹扩展速率之间; 载荷保持加速裂纹扩展。在试验结果的基础之上

针对 Ni3Al合金建立了一个热 /机械疲劳扩展速率线性累积模型

并应用该模型对两个验证试验进行了检验

结果表明

该线性累积模型预测结果与试验数据吻合得很好。

Abstract

In this paper

the experimental study and the analysis about the behavior of thermal mechanical fatigue (TMF) crack growth were conducted in Ni 3Al superalloy

with thermal cycle of 450℃ to 990℃.The effects of phase angle

load hold

temperature and frequency on thermal mechanical fatigue crack growth rate in Ni 3Al superalloy

respectively

were studied.A predictable model about thermal mechanical crack growth rate in Ni 3Al superalloy is proposed.The key results drawn from this study are as follows:Increasing temperature and decreasing frequency accelerate crack growth rate;The crack growth rate of in phase thermal mechanical fatigue is much larger than that of out phase thermal mechanical fatigue and both of them are between the crack growth rates of 450℃ isothermal and 990℃ isothermal tests;Load hold also accelerates crack growth.A linear summation model is proposed about thermal mechanical fatigue crack rate in Ni3Al superalloy based on these experimental results.This model is composed of cycle dependent component and time dependent component.And two proof tests were conducted to verify this model.The results predicted by this linear summation model agree well with experimental data.

关键词

Keywords

references

Views

401

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Thermal fatigue behavior of nickle based superalloy GH536

Investigation of thermal fatigue failure characteristics on typical cooling laminated configurations

Study of failure mode and failure mechanisms on thermal fatigue of plasma sprayed thermal barrier coatings

Study on thermal fatigue life prediction for plasma sprayed thermal barrier coatings on the surface of turbine vane

An Experimental Study of Oxidation and Thermal Fatigue of TBC

Related Author

杨晓光

易靖钦

苗国磊

石多奇

陈静

DU Zhi-neng

ZHANG Cui-hua

SHI Yan

Related Institution

北京航空航天大学能源与动力工程学院

先进航空发动机协同创新中心

School of Power and Energy Engineering, Beijing University of Aeronautics and Astronautics

Shenyang Engine Design and Research Institute, Aviation Industry Corporation of China

School of Jet Propulsion, Beijing University of Aeronautics and Astronautics

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰