Compare of plug nozzle's heat transfer characteristics in different opertoin condition and with different coolant flow rate

HAN Fei; LIU Yu; LI Jun-wei

Chinese

您当前的位置：

首页 >

文章列表页 >

Compare of plug nozzle's heat transfer characteristics in different opertoin condition and with different coolant flow rate

更新时间：2026-07-07

- Compare of plug nozzle's heat transfer characteristics in different opertoin condition and with different coolant flow rate
- Vol. 21, Issue 4, (2006)
- 作者机构：
  
  北京航空航天大学宇航学院,北京,100083
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2006
- 稿件说明：
移动端阅览
HAN Fei, LIU Yu, LI Jun-wei. Compare of plug nozzle's heat transfer characteristics in different opertoin condition and with different coolant flow rate[J]. 2006, 21(4).
DOI：

HAN Fei, LIU Yu, LI Jun-wei. Compare of plug nozzle's heat transfer characteristics in different opertoin condition and with different coolant flow rate[J]. 2006, 21(4). DOI：

摘要

为了解塞式喷管发动机高低空不同的再生冷却换热特性

分别对二维型面内喷管和塞锥建立计算模型

采用数值模拟的方法

得出内喷管的冷却换热结果和出口参数

重点研究了塞锥在地面和设计点工作时的不同换热特性及其冷却剂流量的影响。计算过程中采用二阶迎风格式离散控制方程。计算结果表明:地面工况下

冷却剂流量的改变对塞锥和塞锥底部壁面的压强、热流密度和温度的影响较大

高空环境下

冷却剂流量的改变对塞锥和塞锥底部壁面的压强、热流密度的影响较小;在冷却剂流量相同的情况下

塞锥和塞锥底部在地面工况下的壁面温度要远高于在高空环境下的温度;在相同工况和相同冷却剂流量的情况下

塞锥壁面上的温度要远高于塞锥底部壁面上的温度。

Abstract

To understand the different heat transfer characteristics of regenerative cooling in plug nozzle at different operating conditions

computational model of two dimensional plug nozzle and internal nozzle were established and numerical simulation was employed.Heat transfer results of the internal nozzle and the parameter distribution at the outlet were obtained.Flowfield and heat transfer characteristics of the plug at different operating conditions with different coolant flow rates were investigated.For calculation

governing equations were discretized with second order upstream scheme.The results show that at sea level

coolant flow rate affects the plug pressure

heat flux and temperature;at design operating condition

coolant flow rate has no effect on pressure and heat flux on the plug wall.With the same coolant flow rate

plug temperature at sea level is higher than that at design operating condition;under the same operating condition

ramp temperature is higher than the plug base temperature.

关键词

Keywords

references

Views

480

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effects of gap between nozzles on plug heat transfer characteristics

Heat transfer characteristics of axi-symmetrical nozzle and RS nozzle

Heat transfer characteristics of expander cycle thrust chamber

Heat transfer characteristics of expander cycle thrust chamber with different cooling routing

3D heat transfer investigation on plug nozzle in different operation condition

Related Author

QIN Li-zi

ZHANG Hong-wei

TAO Wen-quan

HE Ya-ling

FENG Zhen-ping

WANG Yi-bai

WANG Chang-hui

SHAO Wan-ren

Related Institution

State Key Laboratory of Multiphase Flow in Power EngineeringXi'an Jiaotong University

School of Jet Propulsion, Beijing University of Aeronautics and Astronautics

Shenyang Aeroengine Research Institute, Aviation Industry Corporation of China

Institute of Engineering Thermophysics, Chinese Academy of Sciences

Graduate School of Chinese Academy of Sciences

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰