Heat transfer characteristics of expander cycle thrust chamber with different cooling routing

HAN Fei; LIU Yu

Chinese

您当前的位置：

首页 >

文章列表页 >

Heat transfer characteristics of expander cycle thrust chamber with different cooling routing

更新时间：2026-07-07

- Heat transfer characteristics of expander cycle thrust chamber with different cooling routing
- Vol. 21, Issue 6, (2006)
- 作者机构：
  
  北京航空航天大学宇航学院,北京,100083
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2006
- 稿件说明：
移动端阅览
HAN Fei, LIU Yu. Heat transfer characteristics of expander cycle thrust chamber with different cooling routing[J]. 2006, 21(6).
DOI：

HAN Fei, LIU Yu. Heat transfer characteristics of expander cycle thrust chamber with different cooling routing[J]. 2006, 21(6). DOI：

摘要

为了解液体火箭发动机膨胀循环推力室再生冷却换热特性

对某一参考发动机推力室和另外两种面积比的膨胀循环推力室建立三维计算模型

采用数值模拟的方法

考察冷却剂的温升、冷却通道压降以及推力室内壁面温度和热流密度的分布情况。重点比较了不同燃烧室圆柱段长度、冷却剂不同流动方式以及不同面积比对以上结果的影响。计算过程中采用二阶迎风格式离散控制方程。计算结果表明:采用逆流冷却时

通过加长推力室圆柱段长度使推力室受热面积增加70%后

冷却剂温升提高了一倍左右;对膨胀循环推力室进行再生冷却时

采用顺流冷却要比逆流冷却的冷却通道压降低

但同时冷却剂温升也较低

并且对喉部壁面的冷却效果较差。

Abstract

To study the heat transfer characteristics of expander cycle regeneratively-cooled thrust chamber

three dimension computational models of a referenced thrust chamber and two expander cycle thrust chambers with different area ratio were established.The coolant heat pick-up

pressure loss in the cooling circuit

wall temperature and heat flux distribution were calculated by numerical simulation.Influence of increased length of chamber cylinder

different cooling routing and area ratio were investigated.Governing equations were discrete with two order upstream scheme.Numerical results show that when a converse cooling is taken

the area of hot gas wall surface of chamber is increased 70% by increased length of chamber cylinder and the coolant heat pick-up is increased about as much as one time;while the selected co-flow cooling routing is employed

the pressure loss is decreased in cooling circuit but the coolant heat pick-up is less than the converse cooling and this cooling routing leads higher wall temperature at the throat.

关键词

Keywords

references

Views

478

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Heat transfer characteristics of expander cycle thrust chamber

Effects of gap between nozzles on plug heat transfer characteristics

Heat transfer characteristics of axi-symmetrical nozzle and RS nozzle

3D heat transfer investigation on plug nozzle in different operation condition

Compare of plug nozzle's heat transfer characteristics in different opertoin condition and with different coolant flow rate

Related Author

LI Jun-wei

ZHANG Hong-wei

TAO Wen-quan

HE Ya-ling

FENG Zhen-ping

QIN Li-zi

Shaotong XU

Changhui WANG

Related Institution

State Key Laboratory of Multiphase Flow in Power EngineeringXi'an Jiaotong University

School of Astronatuics，Beihang University

School of Jet Propulsion, Beijing University of Aeronautics and Astronautics

Shenyang Aeroengine Research Institute, Aviation Industry Corporation of China

School of Astronautics,Beihang University

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰