Experimental research on the cooling characteristics of an afterburner fuel injector with double-wall construction

YAN Bao-hua; FAN Wei-jun; LI Rui-ming; YANG Mao-lin

Chinese

您当前的位置：

首页 >

文章列表页 >

Experimental research on the cooling characteristics of an afterburner fuel injector with double-wall construction

更新时间：2026-07-07

- Experimental research on the cooling characteristics of an afterburner fuel injector with double-wall construction
- Vol. 23, Issue 10, (2008)
- 作者机构：
  
  北京航空航天大学能源与动力工程学院,北京,100191
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2008
- 稿件说明：
移动端阅览
YAN Bao-hua, FAN Wei-jun, LI Rui-ming, et al. Experimental research on the cooling characteristics of an afterburner fuel injector with double-wall construction[J]. 2008, 23(10).
DOI：

YAN Bao-hua, FAN Wei-jun, LI Rui-ming, et al. Experimental research on the cooling characteristics of an afterburner fuel injector with double-wall construction[J]. 2008, 23(10). DOI：

摘要

根据实际需要

提出了新型外涵引气双层壁喷油杆的结构方案.共设计了不同结构尺寸的8种新型双层喷油杆冷却套

在流动特性研究的基础上进一步对其换热特性和高温工况下流动性能进行了对比实验.综合其引气和冷却性能

对比八种尺寸套管

选取了较为合适的冷却套管结构尺寸.并对这种尺寸的套管进行了油杆内壁温度沿杆高的变化、油杆内壁温度随冷却气总压的变化及油杆内壁温度随套管进口雷诺数的变化的研究.实验表明:可以有效从外涵引气(压差850 Pa时

引气量9 g/s)

能够较大降低油杆内壁温度(冷却效率0.7以上).

Abstract

A new afterburner fuel injector with double-wall construction was presented to meet the actual requirements.8 test pieces of new fuel injector casings with different sizes were designed in this research.The heat transfer characteristics and cooling air flow performance were tested based on previous flow characteristics research.In view of the air extraction and cooling performance

an optimum cooling case was selected.Then

this casing of fuel injector was researched with respect to the distribution of injector temperature

change of injector temperature with cooling flow inlet total pressure and change of injector temperature with Re of cooling flow inlet.The results show that: this new afterburner fuel injector can extract enough cooling air from the fan stream(When Δp is 850 Pa

extracted air flow flux is 9 g/s) and decrease effectively the temperature of the wall of fuel injector(cooling efficiency is not less than 0.7).

关键词

Keywords

references

Views

461

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Preliminary experiment on the lean blow-off of an integrated cavity-based strut flameholder

Numerical simulation on improved integrated afterburner scheme

Numerical simulation on infrared radiation characteristics of round to rectangular nozzles with different chevrons considering engine components

Cooling performance and comparison of impingement/effusion cooling lamilloy used as heat shield

考虑多源不确定性的复合材料风扇叶片高周疲劳失效概率评估

Related Author

XIE Yi

ZHOU Chunyang

LIU Yuying

覃文隆

石强

樊未军

张荣春

尹成茗

Related Institution

北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室

Shenyang Engine Design and Research Institute, Aviation Industry Corporation of China

School of Energy and Power Engineering,Beijing University of Aeronautics and Astronautics

Department of Conceptual Design, Chengdu Aircraft Design and Research Insititute, Aviation Industry Corporation of China

College of Energy and Power Engineering,Nanjing University of Aeronautics and Astronautics

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰