Experiment of the effects of geometrical parameters on internalheat transfer in an impinging contraction channel with liquid crystal transient technique

ZHOU Lei-sheng; ZHU Hui-ren; ZHANG Xia; LI Chun-lin

Chinese

您当前的位置：

首页 >

文章列表页 >

Experiment of the effects of geometrical parameters on internalheat transfer in an impinging contraction channel with liquid crystal transient technique

更新时间：2026-07-07

- Experiment of the effects of geometrical parameters on internalheat transfer in an impinging contraction channel with liquid crystal transient technique
- Vol. 25, Issue 8, (2010)
- 作者机构：
  
  西北工业大学动力与能源学院,西安,710072
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2010
- 稿件说明：
移动端阅览
ZHOU Lei-sheng, ZHU Hui-ren, ZHANG Xia, et al. Experiment of the effects of geometrical parameters on internalheat transfer in an impinging contraction channel with liquid crystal transient technique[J]. 2010, 25(8).
DOI：

ZHOU Lei-sheng, ZHU Hui-ren, ZHANG Xia, et al. Experiment of the effects of geometrical parameters on internalheat transfer in an impinging contraction channel with liquid crystal transient technique[J]. 2010, 25(8). DOI：

摘要

采用窄带热色液晶全表面瞬态测温技术

对将涡轮发动机进气道支板的冲击腔进行放大和简化后所得的收缩型通道内表面开展冲击换热实验研究

具体考察了射流孔孔径、冲击距以及通道高度变化对努塞尔数分布及大小的影响.实验结果表明:孔径和通道高度的增大、冲击距的减小均使通道内部换热得以加强

但在侧壁和前缘的努塞尔数分布变化及平均努塞尔数增幅不尽相同;并且通道内部换热受孔径影响最大

受通道高度的影响最小.

Abstract

An impinging heat transfer experiment in a contraction channel

obtained by simplifying and magnifying the strut in the inlet of a gas turbine engine

was carried out by adopting narrow-band thermochromic liquid crystal(TLC) transient measurement technique.The effects of the diameter of impingement hole

impingent distance and the height of the channel on Nusselt number distribution and quantities were studied.The results show that the heat transfer in the channel was enhanced with the increasing diameter of the impingent holes and the height of the channel

or the decreasing impingent distance.Meanwhile the distribution change of Nusselt number and the increase of mean Nusselt number on the sidewall and the leading edge are different.In addition

the primary dominating factor for the heat transfer in the channel is the diameter of the impinging holes

and the slightest factor is the height of the channel.

关键词

Keywords

references

Views

449

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Experimental investigation of heat transfer characteristic in turbine casing

Heat transfer measurements of turn-over channel in turbine blade

Experiment of impingement heat transfer with film holes bleeding and side bleeding

Numerical analysis of hot launch of missile from a launch canister

Experimental and numerical study on pulsed-jet impingement heat transfer with an additional collection chamber

Related Author

ZHANG Shu-hua

ZHANG Li

XU Du-chun

WANG Xiao-zeng

ZHANG Li

ZHU Hui-ren

LIANG Wei-ying

WANG Ke-fei

Related Institution

School of Power and Energy, Northwestern Polytechnical University

School of Mechanical Engineering，Nanjing University of Science and Technology

南京航空航天大学能源与动力学院江苏省航空动力系统重点实验室

南京工程学院能源与动力工程学院

西北工业大学燃烧、热结构与内流场重点实验室

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰