Laser shock processing and aluminizing compound technology used on steel blade

LI Ying-hong; LI Wei; HE Wei-feng; LI Yu-qin; LI Qi-peng

Chinese

您当前的位置：

首页 >

文章列表页 >

Laser shock processing and aluminizing compound technology used on steel blade

更新时间：2026-07-07

- Laser shock processing and aluminizing compound technology used on steel blade
- Vol. 26, Issue 11, (2011)
- 作者机构：
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2011
- 稿件说明：
移动端阅览
LI Ying-hong, LI Wei, HE Wei-feng, et al. Laser shock processing and aluminizing compound technology used on steel blade[J]. 2011, 26(11).
DOI：

LI Ying-hong, LI Wei, HE Wei-feng, et al. Laser shock processing and aluminizing compound technology used on steel blade[J]. 2011, 26(11). DOI：

摘要

采用扫描电子显微镜(SEM)

X射线衍射(XRD)等手段研究了激光冲击强化(LSP)对钢制叶片渗铝层的影响

结果表明渗铝后进行激光冲击强化会对渗铝层造成破环

而在渗铝之前进行激光冲击强化则能提高渗层质量.从残余应力和显微组织变化两方面分析了渗铝高温作用对不锈钢材料激光冲击强化效果的影响

激光冲击强化产生的残余压应力在510℃渗铝温度环境下保温150min仍有-295MPa稳定存在

晶粒细化组织也没有明显长大

激光冲击不锈钢材料的残余应力和微观组织具有良好的热稳定性.振动疲劳对比试验结果验证了“LSP+渗铝”组合工艺对不锈钢材料的强化效果

在660MPa应力水平下

采用该组合工艺试片的疲劳寿命为3.98×106

为原渗铝试片疲劳寿命的14倍左右.

Abstract

Scanning electron microscopy (SEM)

X-ray diffraction (XRD) and other techniques were used to detect the influence of laser shock processing (LSP) on aluminizing layer

which is infiltrated into the stainless steel blade for antisepticising.The results show that the aluminizing layer will be destroyed when LSP is implemented after aluminizing.And the quality of aluminizing layer will be improved while LSP is implemented before aluminizing.The influence on the LSP by the high temperature in the course of aluminizing was studied through residual stress test and metallographic analysis.After 150 minutes in the condition of aluminizing temperature 510℃

the residual compressive stress in the LSP zone was still -295MPa and the refined grain did not grow up remarkably.The residual compressive stress and grain refinement layer induced by LSP had good thermo stability.Finally

the vibration fatigue performance of different states stainless steels was tested.When the maximum stress is 660MPa

the fatigue life of “LSP before aluminizing” is about 3.98 ×106

which is about fourteen times than that of aluminizing.

关键词

Keywords

references

Views

104

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Assessment research on damage degree of blade in aero-engine based on back-propagation artificial neural networks

RELIABILITY OF ENGINE BLADE NONDESTRUCTIVE TESTING

LQ/controller design for aero-engine based on improved NSGAⅡ

Mathematical model of isentropic expansion process based onfunction

Investigation on the performance of an ultrasonic/pressure-swirl hybrid injector

Related Author

QIAN Zheng-wen

CHENG Li

ZHAO Bing-bing

LI Ying-hong

Liu Dengdi

Fu Huimin

WANG Yuan

LI Qiu-hong

Related Institution

The Engineering Institute, Air Force Engineering University

State Key Laboratory for Manufacturing Systems Engineering, School of Mechanical Engineering, Xi'an Jiaotong University

th Dept.Beijing University of Aeronautics and Astronautics

Jiangsu Province Key Laboratory of Aerospace Power System, College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics

College of Energy and Power Engineering,Nanjing University of Aeronautics and Astronautics

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰