Grinding wheel dressing method for inner helical gear form grinding based on numerical simulation

SU Jian-xin; DENG Xiao-zhong; REN Xiao-zhong; XU Kai

Chinese

您当前的位置：

首页 >

文章列表页 >

Grinding wheel dressing method for inner helical gear form grinding based on numerical simulation

更新时间：2026-07-07

- Grinding wheel dressing method for inner helical gear form grinding based on numerical simulation
- Vol. 26, Issue 10, (2011)
- 作者机构：
  
  1. 西北工业大学机电学院,西安,71007
  2. 河南科技大学机电工程学院,河南,洛阳,471003
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2011
- 稿件说明：
移动端阅览
SU Jian-xin, DENG Xiao-zhong, REN Xiao-zhong, et al. Grinding wheel dressing method for inner helical gear form grinding based on numerical simulation[J]. 2011, 26(10).
DOI：

SU Jian-xin, DENG Xiao-zhong, REN Xiao-zhong, et al. Grinding wheel dressing method for inner helical gear form grinding based on numerical simulation[J]. 2011, 26(10). DOI：

摘要

针对内斜齿轮数控成形磨削中较难解决的磨削干涉问题

研究了内斜齿轮成形磨削的砂轮修形方法.在建立内斜齿轮成形磨削数学模型的基础上

用截圆法得到磨削内斜齿轮时砂轮与齿槽接触点所满足的条件方程组

通过牛顿迭代法解此方程组求出砂轮廓形.用数值法模拟出所求砂轮的实际磨削齿形并与理论渐开线齿形作比较

以检验磨削是否干涉及砂轮半径和安装角的选取是否正确.基于 Visual C++ 6.0 编制内斜齿轮砂轮修形及误差分析软件

通过仿真正确选择砂轮安装角、砂轮半径

并输出数控砂轮修整程序.最后通过磨削和检测实例

验证了理论的正确性和软件的可行性.

Abstract

In view of grinding interference produced in the process of inner helical gear form grinding

the grinding wheel dressing method for the inner helical gear form grinding was studied.On the basis of establishing the mathematical model of inner helical gear form grinding

the conditional equations sets conforming to the contact points between grinding wheel and tooth space were obtained by means of circle cutting

and then the wheel profile was found through solving the equations by using Newton iteration.The practical profile of wheel simulated by numerical method was compared with the theoretical involute tooth to inspect whether the gear grinding causes interference

and whether the radius of grinding wheel and its installation angle are correct.Wheel dressing and simulating analysis software was prepared based on Visual C++ 6.0

which can be used to select the grinding wheel radius and installation angle

and output the computer numerical control (CNC) program for dressing form grinding wheel.The practical inner helical gear grinding test and inspection results show that the dressing method is correct and the dressing software is feasible.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Simulation method of short crack propagation in turbine disks based on crystal plasticity

Numerical simulation of internal flow field in gas generator of fire extinguishing bomb

Numerical simulation of light-craft effects onlaser supported donation wave with gas-liquid two phase propellant

Low-Reynolds-number wake flows of a triangular prism

Influence of combustor shape on self-ignition in solid fuel scramjet

Related Author

Ping ZHANG

Shan LU

Xin JING

Mao YANG

Zhongbing LUO

Rongxin ZHOU

Yunfeng LI

Kangqing DENG

Related Institution

School of Power and Energy，Northwestern Polytechnical University

Nondestructive Testing and Evaluation Laboratory， Dalian University of Technology

College of Civil Engineering， Hefei University of Technology

Key Laboratory of Aerospace Chemical Power Technology， Hubei Institute of Aerospace Chemical Techologh， China Aerospace Science and Technology Corporation，Xiangyang Hubei

Hubei Institute of Aerospace Chemistry Technology， China Aerospace Science and Technology Corporation，Xiangyang Hubei

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰