Quasi-steady flow model of slot-type casing treatments Ⅱ: design optimization of casing treatment for a transonic rotor

FAN Lin; NING Fang-fei; LIU Huo-xing

Chinese

您当前的位置：

首页 >

文章列表页 >

Quasi-steady flow model of slot-type casing treatments Ⅱ: design optimization of casing treatment for a transonic rotor

更新时间：2026-07-07

- Quasi-steady flow model of slot-type casing treatments Ⅱ: design optimization of casing treatment for a transonic rotor
- Vol. 27, Issue 6, (2012)
- 作者机构：
  
  北京航空航天大学能源与动力工程学院,北京,100191
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2012
- 稿件说明：
移动端阅览
FAN Lin, NING Fang-fei, LIU Huo-xing. Quasi-steady flow model of slot-type casing treatments Ⅱ: design optimization of casing treatment for a transonic rotor[J]. 2012, 27(6).
DOI：

FAN Lin, NING Fang-fei, LIU Huo-xing. Quasi-steady flow model of slot-type casing treatments Ⅱ: design optimization of casing treatment for a transonic rotor[J]. 2012, 27(6). DOI：

摘要

对带气室的槽道式处理机匣的结构进行了参数化

然后采用所发展的处理机匣流动模型对槽道式处理机匣进行了数值模拟分析

获得了槽道式处理机匣各主要结构参数对处理机匣扩稳作用和转子效率的影响.基于原基准处理机匣

并选取各个结构参数经分析得到的最优值设计了一个优化的处理机匣.实验结果表明:优化的处理机匣设计在60%

80%

98%设计转速下都在原基准处理机匣的基础上进一步提高了转子的失速裕度

并且带有优化处理机匣的转子峰值效率比基准处理机匣、甚至实壁机匣的情形都有所提高.另外

为考察处理机匣槽道数的影响

对一个在优化处理机匣的基础上缩减槽道数而得到的处理机匣设计也进行了实验研究.

Abstract

A geometrical parameterization method for the slot-type casing treatment was presented.The relation between a set of key geometrical parameters and the casing treatment performance was obtained based on the numerical simulations of the slot-type casing treatments using the developed quasi-steady casing treatment flow model.Then

an optimized casing treatment was obtained based on the previously designed baseline casing treatment and by the selection of the optimal geometrical parameters.The subsequent experiment shows that the optimized casing treatment can further improve the stall margin over that using the baseline casing treatment.Moreover

the rotor peak efficiency using the optimized casing treatment is also improved the speeds of at 60%

80% and 98% as compared to that of the baseline casing treatment case and even the solid built.Additionally

to investigate the effect of the number of slots

the experimental study of a casing treatment which was the same as the optimized one but with different slot number was also performed.

关键词

Keywords

references

Views

569

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Quasi-steady flow model of slot-type casing treatments Ⅰ: modeling method and validation

Design of a slot-type casing treatment and its experimental validation

Modeling simulation and optimization of oil system based on MATLAB/Simulink

Experimental investigation about the circumferential treating angle of non-axisymmetric casing treatments

Plenum chamber casing treatment——numerical research of internal flow and mechanism of stall margin improvements

Related Author

LIU Li-wei

FAN Lin

LIU Huo-xing

NING Fang-fei

闫星辉

郭迎清

殷锴

刘国建

Related Institution

School of Jet Propulsion, Beijing University of Astronautics and Aeronautics

西北工业大学动力与能源学院

中国航空发动机集团有限公司商用航空发动机有限责任公司

National Key Lab on Aero-Engine, School of Jet PropulsionBeijing University of Aeronautics and Astronautics

Shenyang Aero Engine Research Institute

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰