Structural parameter design of slot injection control for rectangle mix-compression inlet

YOU Jin; XIA Zhi-xun; LIU Bing; LV Zhong

Chinese

您当前的位置：

首页 >

文章列表页 >

Structural parameter design of slot injection control for rectangle mix-compression inlet

更新时间：2026-07-07

- Structural parameter design of slot injection control for rectangle mix-compression inlet
- Vol. 27, Issue 7, (2012)
- 作者机构：
  
  国防科学技术大学航天与材料工程学院,长沙,410073
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2012
- 稿件说明：
移动端阅览
YOU Jin, XIA Zhi-xun, LIU Bing, et al. Structural parameter design of slot injection control for rectangle mix-compression inlet[J]. 2012, 27(7).
DOI：

YOU Jin, XIA Zhi-xun, LIU Bing, et al. Structural parameter design of slot injection control for rectangle mix-compression inlet[J]. 2012, 27(7). DOI：

摘要

针对窄缝形主动射流用于二元混压式超声速进气道再起动特性调节的结构参数设计

开展了大量定常数值模拟研究

得到了窄缝位置、宽度及喷射角度等结构参数对再起动特性的影响趋势

利用少量非定常算例验证了定常计算结果的准确性.结果表明:射流的注入使进气道产生超声速溢流

并出现可动气动喉道等新的再起动流场特征.约进气道流量1%的射流流量能产生约5%的溢流量

在溢流作用下

4.5%~11%的射流流量使进气道实现了再起动

射流流量越大

射流分离区也越大

进气道越难实现再起动.研究还发现:窄缝位置及宽度对射流溢流效率的影响很小

但窄缝位置存在一个有效作用范围

只有在距唇口35~65mm的位置注入射流

进气道才能实现再起动.射流喷射角对射流溢流效率的影响较大.射流喷射角越大

射流的溢流效率越高

再起动所需的射流流量及其范围也越小.

Abstract

Numerical simulation on structural parameter design of slot injection control restarting characteristics of rectangle mix-compression supersonic inlet was conducted.Effects of the slot position

width and injection angle on restarting characteristics were researched.A few unsteady numerical simulations were performed to verify the steady results.The steady calculation results show that new restarting flow impress such as movable pneumatic throat appears

and the supersonic mass spillage increases with the injection.Inlet restarts with the injection mass flux of 4.5%~11% inlet mass flux as 5% inlet mass flux spills out with the injection mass flux of 1% inlet mass flux.When the distance between lip and slot is 35~65mm

inlet would restart and has same restarting characteristics.With the increase of injection angle

spillage efficiency of injection enhances

and the range of injection mass flux for restart reduces.However the effects of slot width on spillage efficiency of injection and restarting characteristics of inlet is slight.

关键词

Keywords

references

Views

666

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Simulation method of short crack propagation in turbine disks based on crystal plasticity

Numerical simulation of internal flow field in gas generator of fire extinguishing bomb

Numerical simulation of light-craft effects onlaser supported donation wave with gas-liquid two phase propellant

Low-Reynolds-number wake flows of a triangular prism

Influence of combustor shape on self-ignition in solid fuel scramjet

Related Author

Ping ZHANG

Shan LU

Xin JING

Mao YANG

Zhongbing LUO

Rongxin ZHOU

Yunfeng LI

Kangqing DENG

Related Institution

School of Power and Energy，Northwestern Polytechnical University

Nondestructive Testing and Evaluation Laboratory， Dalian University of Technology

College of Civil Engineering， Hefei University of Technology

Key Laboratory of Aerospace Chemical Power Technology， Hubei Institute of Aerospace Chemical Techologh， China Aerospace Science and Technology Corporation，Xiangyang Hubei

Hubei Institute of Aerospace Chemistry Technology， China Aerospace Science and Technology Corporation，Xiangyang Hubei

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰