Internal contraction tunnel design of two-dimensional hypersonic inlet

LI Hang; LI Bo

Chinese

您当前的位置：

首页 >

文章列表页 >

Internal contraction tunnel design of two-dimensional hypersonic inlet

更新时间：2026-07-07

- Internal contraction tunnel design of two-dimensional hypersonic inlet
- Vol. 28, Issue 6, (2013)
- 作者机构：
  
  1. 南京航空航天大学能源与动力学院,南京,210016
  2. 中国人民解放军92724部队,山东,青岛,266000
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2013
- 稿件说明：
移动端阅览
LI Hang, LI Bo. Internal contraction tunnel design of two-dimensional hypersonic inlet[J]. 2013, 28(6).
DOI：

LI Hang, LI Bo. Internal contraction tunnel design of two-dimensional hypersonic inlet[J]. 2013, 28(6). DOI：

摘要

针对二元高超声速进气道

采用不同张度的样条曲线设计内压段肩部型面.在保持二元进气道内压段面积收缩比及喉道面积不变的条件下

通过数值仿真研究了不同内压段长度、下壁面型面样条曲线张度对进气道性能的影响.结果表明:内压段的长度变化对进气道的气动及起动性能有较大影响

当内压段长度与喉道高度比 L/ht为8.4左右时总压恢复系数较优;采用合适张度的样条曲线代替传统的肩部圆弧过渡

能够提高进气道总压恢复系数

改善进气道起动性能;随着内压段长度增加

其所对应的性能最优样条线张度值不断减小

建议选取样条线张度值为0.80~1.25.

Abstract

The curved surface of internal contraction tunnel of two-dimensional hypersonic inlet was designed and investigated.Based on hypersonic inlet with the same internal contraction area ratio and throat area

the influences of the length of internal contraction tunnel and the tension of the shoulder spline on the inlet performance were studied numerically.Results indicate that the length of internal contraction tunnel has great effect on the total pressure recovery coefficient and the starting-up Mach number.When the length to throat height ratio is 8.4

the total pressure recovery coefficient is better.Spline with suitable tension to replace the traditional surface with radii at shoulder can increase the total pressure recovery coefficient.With the increase of the length of internal contraction tunnel

the corresponding optimal tension of spline will decrease.The recommended range of spline tension is 0.80-1.25.

关键词

Keywords

references

Views

1012

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Accurate prediction method of flow coefficient for 2D curved surface variable inlet

Parameters analysis of adaptive pressure relief slot in hypersonic inlet

Design of hypersonic inward turning inlets base on concept of controllable Mach number distribution

Unsteady characteristics of hypersonic inlet below self-starting Mach number

Research on aerodynamic characteristics of 2-D hypersonic inlet

Related Author

李永洲

马元

张堃元

LIU Yuan

JIN Zhi-guang

ZHANG Kun-yuan

NAN Xiang-jun

LI Yong-zhou

Related Institution

中国航天科技集团有限公司西安航天动力研究所

南京航空航天大学能源与动力学院

国防科技大学高超声速冲压发动机技术重点实验室

国防科技大学空天科学学院

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰