Influence of wheel spokes structure on the distribution of surface water film during the wading of road vehicle

HU Xingjun; YAO Hongyi; GUO Peng; YANG Hanbo; YANG Bo

doi:10.11918/j.issn.0367-6234.201607124

Chinese

您当前的位置：

首页 >

文章列表页 >

Influence of wheel spokes structure on the distribution of surface water film during the wading of road vehicle

更新时间：2026-10-19

- Influence of wheel spokes structure on the distribution of surface water film during the wading of road vehicle
- Vol. 49, Issue 7, Pages: 2017-7(2017)
- 作者机构：
  
  1. 汽车仿真与控制国家重点实验室(吉林大学),长春,130025
  2. 吉林大学汽车工程学院,长春,130025
  3. [KH-*1]
  4. 中国第一汽车集团公司技术中心,长春,130011
- 作者简介：
- 基金信息：
- DOI：10.11918/j.issn.0367-6234.201607124
  CLC： U461.1
- Published：2017
- 稿件说明：
移动端阅览
HU Xingjun, YAO Hongyi, GUO Peng, et al. Influence of wheel spokes structure on the distribution of surface water film during the wading of road vehicle[J]. 2017, 49(7): 2017-7.
DOI：

HU Xingjun, YAO Hongyi, GUO Peng, et al. Influence of wheel spokes structure on the distribution of surface water film during the wading of road vehicle[J]. 2017, 49(7): 2017-7. DOI： 10.11918/j.issn.0367-6234.201607124.

摘要

针对汽车涉水时车身表面的水污染问题，将传统的汽车空气动力学知识和多相流理论相结合，运用图像处理技术给出车身表面水膜分布情况.通过对车轮辐板进行改型，建立不同开孔数目和开孔面积的车轮辐板模型，分析对比不同开孔数目和开孔面积对水膜分布情况的影响.试验结果表明，4种不同开孔数的辐板中，T7的涉水性能最优越，水膜覆盖率较原始值降低了20.67%.车轮辐板开孔有助于提高车辆的涉水性能，开孔数目越少车身表面的水相附着面积也越小.车轮辐板开孔数目相同时，车表水相附着面积随着开孔面积的增大而增大.

Abstract

As for the vehicle surface water pollution problem during the car wading

this paper combined the traditional automotive aerodynamics expertise and multiphase theory to research the water film distribution with the image processing technology. Through modifying the wheel plate

the influence of the number of holes and the opening area on the distribution of water film was analyzed and compared. After the experiment

T7 model had the most perfect wading performance of the four different wheel plate opening holes number in this paper. The water film distribution ratio decreased by 20.67% compared with the original value. We can know that the spoke structure is conductive to improve the wading performance and the less number of spoke has the smaller water phase attachment on the vehicle body surface. When the opening area increase under the same number of wheel plate the water phase attachment area will also increase.

关键词

Keywords

references

Views

557

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Improvement of the non-linear eddy viscosity model applied to predicting wind flow around building

Hydrodynamic characteristics and motion simulation of flying-wing dish-shaped autonomous underwater glider

Analysis and control of water phase of side window based on Boltzmann method

Numerical analysis on blowing-suction cleaning flow field between subway rails

Optimization and verification of dynamic flow balance valve structure

Related Author

LI Biao

ZHAO Jianing

LIU Jing

SHAO Jiantao

ZHANG Chengju

WEI Yingjie

WANG Cong

WANG Jinqiang

Related Institution

School of Municipal and Environmental Engineering, Harbin Institute of Technology

East China Architectural Design ＆ Research Institute Co. Ltd.

State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology

School of Astronautics, Harbin Institute of Technology

State Key Laboratory of Automobile Simulation and Control, Jilin University

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰