Research of civil aviation engine overhaul workscope based on genetic algorithm

赵洪利; 陈铎文; 张智华

doi:10.13224/j.cnki.jasp.2017.08.020

Chinese

您当前的位置：

首页 >

文章列表页 >

Research of civil aviation engine overhaul workscope based on genetic algorithm

更新时间：2026-07-07

- Research of civil aviation engine overhaul workscope based on genetic algorithm
- Vol. 32, Issue 8, Pages: 1962-1970(2017)
- 作者机构：
  
  1. 中国民航大学航空工程学院,天津,300300
  2. 中国民航大学中欧航空工程师学院,天津,300300
- 作者简介：
- 基金信息：
- DOI：10.13224/j.cnki.jasp.2017.08.020
  CLC：
- Published：2017
- 稿件说明：
移动端阅览
赵洪利, 陈铎文, 张智华. 基于遗传算法的民用航空发动机送修方案决策研究[J]. 航空动力学报, 2017, 32(8): 1962-1970.

doi: 10.13224/j.cnki.jasp.2017.08.020
赵洪利, 陈铎文, 张智华. 基于遗传算法的民用航空发动机送修方案决策研究[J]. 航空动力学报, 2017, 32(8): 1962-1970. DOI： 10.13224/j.cnki.jasp.2017.08.020.

doi: 10.13224/j.cnki.jasp.2017.08.020 DOI：

摘要

为了给航空发动机在整个使用周期内送修方案的制定提供支持，降低发动机使用周期内的大修成本，针对单元体结构的民用航空发动机，基于制造商的发动机维修管理大纲，同时考虑时寿件寿命和单元体超出软时限导致性能衰退而造成发动机送修的情况，设定大修间隔不超过最大送修间隔，建立了一种以送修时间间隔为优化变量，以单位飞行小时送修成本最小为优化目标的发动机大修成本优化模型。采用遗传算法对模型进行求解，并以V2500发动机为例，对其25年里多次返厂送修方案进行了优化，表明当送修次数为6次时返厂大修成本最低，并给出了相应的各单元体的修理级别，该方法可为航空公司制定发动机送修方案提供参考。

Abstract

To support the creation of engine overhaul workscope during its life cycle

and reduce the overhaul cost in its life cycle

based on the engine maintenance management program provided by manufactures

by setting the overhaul interval which is less than the maximum overhaul interval

and taking account of the life of life limited parts and soft time of modules

an engine overhaul cost optimization model was presented in the paper for a modular engine

which took the overhaul interval as the variable and the least shop visit cost per flight hour as a target

the genetic algorithm was used to solve this optimization problem. Taking V2500 as an example

its shop visit workscope was optimized

it gave that 6 shop visits in 25 years have the lowest cost

and the repair levels of each module were also created for each shop visit. It can provide a reference method for airlines to make engine workcope for shop visit.

关键词

Keywords

references

Views

561

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Identification of flexible nozzle torque properties based on wavelet neural network optimized by genetic algorithm

Rapid prediction method of compressor characteristics with coupling direct and inverse problems

Calculation method of fuel temperature conforming to requirements of airworthiness certification

Airfoil optimization design based on Gaussian process regression and genetic algorithm

Fault diagnosis method of inter-shaft bearing based on adaptive bistable stochastic resonance

Related Author

Hongcheng YANG

Shan LIU

Guangzai JIN

Weiwei JIAO

Yufeng JIANG

Zhaoyun SONG

Baotong WANG

Tengbo FAN

Related Institution

Laboratory of Aerospace Servo Actuation and Transmission，Beijing Institute of Precision Mechatronics and Controls

Institute for Aero Engine，Tsinghua University

State Key Laboratory of Automotive Safety and Energy，Tsinghua University

Sichuan Gas Turbine Establishment，Aero Engine Corporation of China

Key Laboratory of Aircraft Environmental Control and Life Support of Ministry of Industry and Information Technology，College of Aerospace Engineering，Nanjing University of Aeronautics and Astronautics

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰