Fast and accurate locating method forsculptured surfaces measured with coordinatemeasuring machines based on iterative algorithm

张现东; 卜昆; 董一巍; 李效基

doi:10.13224/j.cnki.jasp.2018.10.026

Chinese

您当前的位置：

首页 >

文章列表页 >

Fast and accurate locating method forsculptured surfaces measured with coordinatemeasuring machines based on iterative algorithm

更新时间：2026-07-07

- Fast and accurate locating method forsculptured surfaces measured with coordinatemeasuring machines based on iterative algorithm
- Vol. 33, Issue 10, Pages: 2525-2532(2018)
- 作者机构：
  
  1. 西北工业大学现代设计与集成制造技术教育部重点实验室,西安,710072
  2. 厦门大学航空航天学院,福建,厦门,361005
- 作者简介：
- 基金信息：
- DOI：10.13224/j.cnki.jasp.2018.10.026
  CLC：
- Published：2018
- 稿件说明：
移动端阅览
张现东, 卜昆, 董一巍, 李效基. 基于迭代算法的复杂曲面零件三坐标测量快速精确定位方法[J]. 航空动力学报, 2018, 33(10): 2525-2532.

doi: 10.13224/j.cnki.jasp.2018.10.026
张现东, 卜昆, 董一巍, 李效基. 基于迭代算法的复杂曲面零件三坐标测量快速精确定位方法[J]. 航空动力学报, 2018, 33(10): 2525-2532. DOI： 10.13224/j.cnki.jasp.2018.10.026.

doi: 10.13224/j.cnki.jasp.2018.10.026 DOI：

摘要

针对复杂曲面零件在三坐标测量过程中存在着定位难、定位精度低的问题

基于改进的迭代最近点算法

提出了考虑半径补偿的预定位与精定位的多级定位算法；并通过建立定位点几何误差与叶片定位精度的数学关系模型

结合贪婪算法与六点原则

给出了近优的定位点序列生成方法。结合定位算法与定位点序列

给出了复杂曲面零件定位迭代流程

并开发了三坐标测量定位系统。以涡轮叶片为例

通过的定位仿真和定位实验

结果表明：该系统只需测量12～18个点即可使得叶片定位误差在0.1mm以内

证明该系统能有效的提高复杂曲面零件的定位精度和效率。

Abstract

The blade is a typical part with sculptured surfaces

the locating of these parts for measurement with coordinate measuring machines (CMM) is a difficult and time-consuming task because there are no locating datum planes. To solve this problem

a multistage location algorithm including pre-location and fine-location

considering radius comprehension

was proposed based on iterative closest point algorithm. By establishing the relationship of locating errors and geometric errors of locating points

a near-optimal locating point sequence was generated using the greedy algorithm and six-point principle. Combining multi-stage location algorithm and locating point sequence

an iterative locating process for the part with sculptured surfaces measurement with CMM was researched and programmed. In the simulation and experiment of localizing a turbine blade with sculptured surfaces

only 12-18 points were need to maintain the location errors with in 0.1mm.The efficiency and accuracy of this method are desirable.

关键词

Keywords

references

Views

415

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

基于三维接触摩擦单元的套齿连接解析建模研究

基于自适应MOMEDA滚动轴承故障特征提取方法

考虑多源不确定性的复合材料风扇叶片高周疲劳失效概率评估

组合式弹性金属密封泄漏特性实验研究与结构优化

与发动机匹配的旁路式双喉道气动矢量喷管数值模拟研究

Related Author

No data

Related Institution

No data

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰