Pressure loss and heat transfer characteristics experiment of swirling impinging jet with different shape nozzles

徐亮; 任德祖; 马永浩; 兰进; 高建民

doi:10.13224/j.cnki.jasp.2018.11.014

Chinese

您当前的位置：

首页 >

文章列表页 >

Pressure loss and heat transfer characteristics experiment of swirling impinging jet with different shape nozzles

更新时间：2026-07-07

- Pressure loss and heat transfer characteristics experiment of swirling impinging jet with different shape nozzles
- Vol. 33, Issue 11, Pages: 2678-2686(2018)
- 作者机构：
  
  西安交通大学机械制造系统工程国家重点实验室,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.13224/j.cnki.jasp.2018.11.014
  CLC：
- Published：2018
- 稿件说明：
移动端阅览
徐亮, 任德祖, 马永浩, 兰进, 高建民. 不同形状喷嘴的旋流冲击射流压力损失和传热特性实验[J]. 航空动力学报, 2018, 33(11): 2678-2686.

doi: 10.13224/j.cnki.jasp.2018.11.014
徐亮, 任德祖, 马永浩, 兰进, 高建民. 不同形状喷嘴的旋流冲击射流压力损失和传热特性实验[J]. 航空动力学报, 2018, 33(11): 2678-2686. DOI： 10.13224/j.cnki.jasp.2018.11.014.

doi: 10.13224/j.cnki.jasp.2018.11.014 DOI：

摘要

提出了一种旋流喷嘴，即圆孔内径设有四条螺旋槽道的类螺纹孔喷嘴。实验对比研究了同一螺旋角下三类旋流喷嘴(插件、内置扭转带、导叶片)与螺纹孔喷嘴在雷诺数为6000、12000下靶面传热特性。分析了各喷嘴对应的气源室压力与流量系数。实验结果表明，螺纹孔喷嘴在靶面的中心区保持了高的传热效率，驻点努塞尔数比其他三种喷嘴高出29.7%~43.3%，当射流空间受限时(半封闭空间)所有喷嘴的努塞尔数下降了40%~60%，内置插件喷嘴下降幅度最大；另外，四种旋流喷嘴中，内置插件喷嘴的气源腔室压力最大，比最小的螺纹孔喷嘴高出一个数量级还多，压力损失系数的分析表明螺纹孔喷嘴的压力损失系数最小，仅是内置插件喷嘴的1/4左右，且雷诺数增大一倍，内置插件喷嘴的压力损失系数平均下降14%，下降幅度最大。

Abstract

A type of swirl nozzle

i.e.

a threaded hole nozzle with four spiral grooves on the diameter of the hole was proposed. The heat transfer characteristics of the three kinds of swirl nozzles (insert

built-in torsion belt and guide vane) with the helical hole nozzle at the same helix angle when the Reynolds numbers were 6000

12000 were investigated. The pressure and flow coefficient of the air supply chamber corresponding to each nozzle were analyzed. The experimental results showed that the spiral hole nozzle had a high heat transfer efficiency in the central area of the target surface

and the stagnation Nusselt number was 29.7%-43.3% higher than the other three nozzles. When the jet space was limited (semi-enclosed space)

the Nusselt number of dropped down by 40% to 60%

and the built-in plug nozzles had the largest drop. In addition

the four kinds of swirl nozzles had the largest air supply chamber pressure of the built-in plug nozzle

one order of magnitude higher than the smallest screw hole nozzle. The analysis of the pressure loss coefficient showed that the pressure loss coefficient of the nozzle hole was the smallest

only about 1/4 of the built-in plug nozzle

the Reynolds number was doubled

and the pressure loss coefficient of the built-in plug nozzle dropped by 14% on average.

关键词

Keywords

references

Views

557

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Numerical simulation of spoiler ring’s effect on combustion and flow of powdered rocket motor

Heat transfer characteristics of a rotating cavity with axial throughflow of cooling air

Effect of the second inlet location on heat transfer distribution in rotating wedgeshaped channel

Anisotropic turbulence model applied to rotating channel

Heat transfer and flow characteristics of low aspect ratio pin-fins in cooling channel

Related Author

胡加明

胡春波

李悦

李超

胡旭

朱小飞

曹楠

窦志伟

Related Institution

西安交通大学化工学院

西北工业大学燃烧、热结构与内流场重点实验室

先进航空发动机协同创新中心

中国航空工业集团有限公司中国直升机设计研究所

北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰