Finite Element Simulation of Three-point Necking Forming Process of TC4 Self-locking Nut

齐增星; 梁铖; 吴同一; 焦光明; 张晓斌; 王宝辉; 张涛; 黎向锋

doi:10.13433/j.cnki.1003-8728.20230118

Chinese

您当前的位置：

首页 >

文章列表页 >

Finite Element Simulation of Three-point Necking Forming Process of TC4 Self-locking Nut

更新时间：2026-07-10

- Finite Element Simulation of Three-point Necking Forming Process of TC4 Self-locking Nut
- Mechanical Science and Technology for Aerospace Engineering Vol. 43, Issue 12, Pages: 2076-2082(2024)
- 作者机构：
  
  1. 天津市紧固连接技术企业重点实验室,天津,300300
  2. 航天精工股份有限公司,天津,300300
  3. 南京航空航天大学机电学院,南京,210016
  4. 空军装备部驻北京地区军事代表局驻天津地区第二军事代表室,天津,300300
- 作者简介：
- 基金信息：
- DOI：10.13433/j.cnki.1003-8728.20230118
  CLC：
- Published：2024
- 稿件说明：
移动端阅览
齐增星, 梁铖, 吴同一, et al. Finite Element Simulation of Three-point Necking Forming Process of TC4 Self-locking Nut[J]. Mechanical Science and Technology for Aerospace Engineering, 2024, 43(12): 2076-2082.
DOI：

齐增星, 梁铖, 吴同一, et al. Finite Element Simulation of Three-point Necking Forming Process of TC4 Self-locking Nut[J]. Mechanical Science and Technology for Aerospace Engineering, 2024, 43(12): 2076-2082. DOI： 10.13433/j.cnki.1003-8728.20230118.

摘要

针对TC4钛合金自锁螺母，利用ABAQUS有限元分析软件，采用单因素控制法开展了对不同收口量、收口区域高度及收口速度的有限元仿真数值模拟研究。基于采用的收口工艺，建立有限元仿真模型，介绍了自锁螺母的成型机理。根据仿真结果，观察其收口过程，分析收口过程中的内螺纹区域应力应变变化规律，对比不同组参数对仿真结果的影响。结果表明：在自锁螺母收口过程中，应在不出现裂纹的合理范围下，尽可能选取较大的收口量、收口区域高度与收口速度，从而增加内螺纹区域的变形量，增大锁紧力矩，提高产品质量和加工效率。

Abstract

Aiming at the TC4 titanium alloy self-locking nut

using ABAQUS and single factor control method

the finite element simulation at different necking volume

necking area height and necking speedare carried out. According to the necking in the enterprises at present

the finite element simulation model is established and the forming mechanism of self-locking nut is introduced. According to the simulation results

the necking processis observed

the changing law of stress and strain in the internal thread area in the neckingis analyzed. Meanwhile compared the effects of different groups of parameters on the simulation results. The results show that in the necking of the self-locking nut

the necking volume

necking area height and necking speed should be selected as large as possible without cracks

so as to increase the deformation of the internal thread area and the locking torque

improve product quality and processing efficiency.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Processing Experiment and Simulation Analysis of Self-piercing Riveting of Low Ductility Aluminum Alloy

Analysis and Verification of Self-weight Influence on Large Deformation of Highly Flexible Cantilever Beams

Study on SPMSM Performance with Bidirectional Sinusoidalized Permanent Magnets

Study on Yield Control Tightening Process and Preload Monitor of Bolted Joints for Wind Turbine Tower

Reverse Identification of J-C Constitutive Parameters of A100 Steel

Related Author

曾凯

邢保英

张洪申

陈忠良

黄俊智

陈浩宇

赵冉

宋巧治

Related Institution

Faculty of Mechanical and Electrical Engineering, Kunming University of Science and Technology

Southwest copper branch, Yunnan Copper Co., Ltd.

School of Aeronautics, Northwestern Polytechnical University

National Key Laboratory of Strength and Structural Integrity

Aircraft Strength Research Institute of China

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰