The Optimization of Drum Water Level Control System for Industrial Boiler

RONG Pan-xiang; GAO Shertg-yu; WANG Zi-xu; WANG Le-tian

doi:10.15938/j.jhust.2015.06.014

Chinese

您当前的位置：

首页 >

文章列表页 >

The Optimization of Drum Water Level Control System for Industrial Boiler

更新时间：2026-08-31

- The Optimization of Drum Water Level Control System for Industrial Boiler
- Vol. 20, Issue 6, Pages: 78-82(2015)
- 作者机构：
  
  哈尔滨理工大学自动化学院,黑龙江,哈尔滨,150080
- 作者简介：
- 基金信息：
- DOI：10.15938/j.jhust.2015.06.014
  CLC： TP273.4
- Published：2015
- 稿件说明：
移动端阅览
RONG Pan-xiang, GAO Shertg-yu, WANG Zi-xu, et al. The Optimization of Drum Water Level Control System for Industrial Boiler[J]. 2015, 20(6): 78-82.
DOI：

RONG Pan-xiang, GAO Shertg-yu, WANG Zi-xu, et al. The Optimization of Drum Water Level Control System for Industrial Boiler[J]. 2015, 20(6): 78-82. DOI： 10.15938/j.jhust.2015.06.014.

摘要

传统的PID控制方法不能完全有效解决汽包水位问题

因为它具有多变性、非线性以及强耦合等特点.因此研究了模糊神经-PID这种控制策略

将模糊神经网络的PID控制器作为给水控制系统的锅炉汽包水位调节器

可实时整定PID控制器参数

以适应控制系统的响应快速性、调节平稳性、及抗干扰能力的要求.仿真结果表明：工业锅炉汽包水位控制系统中可以采用模糊神经-PID控制策略进行优化.

Abstract

The traditional PID control method can not be a fully effective solution of drum level

because it has more variability

nonlinear and strong coupling characteristics. Due to these factors

in this paper

the main discussion is about fuzzy neural PID control strategy. The Fuzzy neural PID controller is adopted as a regulator in the boiler drum＇s water-level control system

the para meters of PID controller can be set in real-time

so as to this controller in aspects of response rapidity

regulation stability

and anti-interference ability. The results showed that the industrial boiler water level control system can be optimized by Fuzzy neural PID control strategy.

关键词

Keywords

references

Views

686

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Simulation and Experimental Analysis of Servo Drive System Using Fuzzy PID Technology of Manipulator Consisting of Electric Steering Gear Based on Orthogonal Optimization

Discrete Equivalent Loading Method for Continuous Structural Distributed Dynamic Loads

Damage Analysis and Optimal Design of Micro-structure Milling Cutter Based on Peridynamics

Localization of Geometric Tolerance Fault Points on the Inner Surface of Compressor Casing

Temperature Prediction Method Based on WTConv-Informer with Frequency Enhanced Channel Attention

Related Author

CHEN Rui

ZHOU Haibo

YU Hengbin

LI Xia

Related Institution

1Tianjin Key Laboratory for Advanced Mechatronic System Design and Intelligent Control, School of Mechanical Engineering, Tianjin University of Technology

2National Demonstration Center for Experimental Mechanical and Electrical Engineering Education, Tianjin University of Technology

3Shandong Labor Vocational and Technical College

AI问答

Postal code：100079
Tel：（010）53879206 Email：tmw@bjxintong.com.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09082226号-64 京公网安备11010602201714号
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰