木结构主次梁新型挂钩件连接节点的受力性能

张文元; 刘辰辰; 丁玉坤; 杨奇勇

doi:10.11918/j.issn.0367-6234.201903098

Chinese

您当前的位置：

首页 >

文章列表页 >

木结构主次梁新型挂钩件连接节点的受力性能

更新时间：2026-10-04

- 木结构主次梁新型挂钩件连接节点的受力性能
- Mechanical performance of a new hanger joint of secondary beam to primary beam in timber structures
- 哈尔滨工业大学学报 2019年51卷第12期页码：128-136
- 作者机构：
  
  1. 结构工程灾变与控制教育部重点实验室(哈尔滨工业大学),哈尔滨,150090
  2. 土木工程智能防灾减灾工业和信息化部重点实验室(哈尔滨工业大学),哈尔滨,150090
  3. 北京国家游泳中心有限责任公司,北京,100101
- 作者简介：
  
  张文元(1972—)，男，教授，博士生导师
- 基金信息：
  
  北京市科技计划项目(D171100001117001)
- DOI：10.11918/j.issn.0367-6234.201903098
  中图分类号： TU366.2
- 纸质出版：2019
- 稿件说明：
移动端阅览
张文元, 刘辰辰, 丁玉坤, 等. 木结构主次梁新型挂钩件连接节点的受力性能[J]. 哈尔滨工业大学学报, 2019,51(12):128-136.

ZHANG Wenyuan, LIU Chenchen, DING Yukun, et al. Mechanical performance of a new hanger joint of secondary beam to primary beam in timber structures[J]. 2019, 51(12): 128-136.
张文元, 刘辰辰, 丁玉坤, 等. 木结构主次梁新型挂钩件连接节点的受力性能[J]. 哈尔滨工业大学学报, 2019,51(12):128-136. DOI： 10.11918/j.issn.0367-6234.201903098.

ZHANG Wenyuan, LIU Chenchen, DING Yukun, et al. Mechanical performance of a new hanger joint of secondary beam to primary beam in timber structures[J]. 2019, 51(12): 128-136. DOI： 10.11918/j.issn.0367-6234.201903098.

摘要

为研究新型木结构主次梁新型金属挂钩件连接节点的受力机理

参照ASTM针对挂钩件的测试标准

进行了8个模型的竖向加载静力试验

得到了节点承载力与主、次梁相对变形曲线和2种典型破坏模式.建立了新型挂钩件节点的ABAQUS三维实体有限元模型

与试验结果和试验现象对照

验证了有限元模型的准确性.采用该模型对挂钩件节点进行参数分析

研究了挂钩件翼缘厚度和宽度对节点抗剪极限承载力和刚度的影响.对挂钩件节点进行详细受力分析

提出了该新型挂钩件节点的简化受力模型

推导了节点的极限承载力计算公式和破坏模式的判别方法

与试验结果吻合良好.

Abstract

To explore the mechanical behavior of a new type of steel hanger joint of secondary beam to primary beam in timber structures

static vertical loading tests of eight specimens using the new hanger joint are carried out based on the ASTM test standards. The load-displacement curves of the joints between the secondary beams and primary beams

as well as two typical failure modes are obtained. By using ABAQUS

three-dimensional solid finite element model of the proposed joint is established. The accuracy of the finite element analysis is verified by comparing with the experimental results. Based on the parametric analysis of the hanger joints

the influence of the thickness and width of the hanger flanges on the shear capacity and stiffness of the joints is studied. Calibrated by the detailed stress analysis and the test results

a simplified mechanical model is proposed

and prediction formulae for the shear capacity and failure modes of the hanger joint are recommended

which are in good agreement with the experimental results.

关键词

Keywords

references

浏览量

157

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

有腹筋UHPFRC梁抗剪承载力计算

冻融损伤混凝土重复受压本构关系

大跨度纺锤形气撑式张弦梁找形分析

RCS混合节点抗剪承载力计算方法对比研究

碳纤维水性上浆剂研究进展